![]() ![]() Steve on On Vim, Modal Interfaces And The Way We Interact With Computers.Piecutter on Finally, A Machine To Organize Resistors!.Andrew on Streaming Video From An ESP32.Paul on Mining And Refining: Quartz, Both Natural And Synthetic.Josh Carlson on Downgrade Your Heathkit H8 To The World’s First 8-bit Microprocessor.CMH62 on Spooky Noise Box Has Post-Halloween Potential.tantris on Road Salt? Bah! New Roadway Material Promises A Better Solution To Snow And Ice.John7 on Downgrade Your Heathkit H8 To The World’s First 8-bit Microprocessor.To Give Is Better Than To Receive 24 Comments Of course, you can get into just about any suitcase with a ball point pen, so maybe this isn’t a real “security” issue, but it sure isn’t what you want to see from the agency that is supposed to protect you. Who knew that you could make keys from a photograph? We did way back in 2009 and way more in depth this May… maybe the TSA should start reading Hackaday?Ĭontinue reading “Dear TSA: This Is Why You Shouldn’t Post Pictures Of Your Keys Online” → Posted in lockpicking hacks, Slider, Transportation Hacks Tagged 3D printed keys, lockpicking, TSA, TSA master key If you put a non-TSA approved lock on the bag, that can make them a little angry, and you risk having your bag delayed or even cut open. So the TSA agents have a set of master keys that can open any bag if they need to look inside for some reason. It has to be approved by the TSA – and that means that they have to be able to open it. You can see it in action in the (twitter) video after the break.įor those that are not familiar with travel in the US, you are not allowed to use just any old lock on your bags. Well, the lock picking community when nuts and in a short time had 3D printed versions available and working. ![]() The most recent TSA folly seemed to practically fall into the Internet’s lap when a reporter for the The Washington Post published a hi-res picture of the entire set of TSA master keys while writing an article about how the TSA handles your bags after checking them at the counter. We’re actually okay with that if it means nobody is trying to do anything shady. If it’s not reports of TSA agents stealing valuables or inappropriately groping passengers, there is the fun fact that in all the years since it was created in 2001, the agency hasn’t caught a single person seeking to do harm in the friendly skies. They seem to have a perfect track record of screwing up – and that’s not an easy thing to accomplish if you think about it. ![]() We have to hand it to the Transportation Security Administration (TSA). Posted in lockpicking hacks, Security Hacks Tagged 3D printed keys, Anycubic Photon, DLP printer, openscad, sla printing, TSA, TSA master key So while the printed keys might not be strong enough for daily use, they’ll certainly work in a pinch. That said, there are some “Tough Resin” formulations available now which produce parts that are at least as strong as those made with thermoplastics. Generally speaking, the parts produced by resin-based printing have a high tensile strength but are very brittle, so perhaps not the kind of thing you want to stick in your expensive Abloy lock. Once you have the decoded values for the key you want to duplicate, you just need to provide them to the OpenSCAD library has developed and print the resulting STL on your sufficiently high-resolution printer. Hopefully this keeps bad actors from doing anything too nefarious with this research. wisely leaves that step of the process out, so anyone looking to use this project will need to have a good working knowledge of the Abloy Protec system. Of course, these keys are far too intricate to duplicate from a single picture, so you’ll need to have the physical key in hand and decode it manually. But with a sub-$300 USD Anycubic Photon DLP printer, it’s now possible to circumvent these highly regarded locks non-destructively. The resulting STLs are, unsurprisingly, beyond the capabilities of your average desktop FDM printer. Inspired by previous printed keys, wanted to see if the techniques could be refined for use against high security Abloy Protec locks, which are noted for their resistance to traditional physical attacks such as picking. The geometry of these keys is far more complex, making them too challenging to duplicate on a consumer-level printer. It’s one thing to print a key that will open a $15 Kwikset deadbolt from the hardware store or a TSA-approved “lock” that’s little more than a toy, but a high-security key is another story. The ability to duplicate keys with a 3D printer is certainly nothing new, but so far we’ve only seen the technique used against relatively low hanging fruit. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |